Features
* High input voltage range: 2.0 V up to 15 V
* Adjustable output voltage: 1.2 V up to 5.5 V
* Up to 75-mA output current
* Up to 800-kHz switching frequency
Detail data, silakan download disini
Harga : Rp 1.399.000,-
Jumat, 19 Agustus 2011
TPS62122 Evaluation Module
Features
* High input voltage range: 2.0 V up to 15 V
* Adjustable output voltage: 1.2 V up to 5.5 V
* Up to 75-mA output current
* Up to 800-kHz switching frequency
Detail data, silakan download disini
Harga : Rp 1.399.000,-
TPS62230/31/32 6V Input, 2.5V Output, 0.5A Evaluation
The TPS62230EVM-370 facilitates evaluation of the TPS62230, TPS62231 or TPS62232 IC. There are three independent circuits on the evaluation module: CKT1 will demonstrate the TPS62230 (2.5V) device. CKT2 will demonstrate the TPS62231 (1.8V) device. CKT3 will demonstrate the TPS62232 (1.2V) device.
Features
* 3 MHz switch frequency
* Up to 94% efficiency
* Output Peak Current up to 500mA
* Excellent AC and Transient Load Regulation
* High PSRR (up to 90dB)
* Small External Output Filter Components 1.0µH/ 4.7µF
* VIN range from 2.05V to 6V
* Optimized Power Save Mode For Low Output Ripple Voltage
* Forced PWM Mode Operation
* Typ. 22 µA Quiescent Current
* 100% Duty Cycle for Lowest Dropout
* Soft Start with typ. 100µs Start Up Time
detail silakan download disini
Harga : Rp 1.399.000,-
TPS780XXEVM-301 Evaluation Module
The TPS780xxEVM-301 demonstrates the TPS780330220 ultra low-power, low dropout (LDO) regulator with pin-selectable, dual output voltage levels. The TPS780330220 comes on the EVM. The EVM can be modified for use with any other products in this family. The EVM provides up to 150 mA while maintaining a low quiescent current of 500 nA. The device is powered from a 2.2 V to 5.5 V source. The output is selectable between 2.2 V and 3.3 V.Features
* 150 mA low dropout regulator with pin-selectable dual voltage level outputs
* Low dropout: 250 mV (typical) at 150 mA
* 3% accuracy over load/line/temperature
* Low Iq: 500 nA (typical)
* Thermal shutdown and overcurrent
Harga : Rp 970.000,-
TPS61220EVM-319 Evaluation Module
Features
* Up to 95% Efficiency
* More than 80% Efficiency at Wide Area of Typical Operating Points
* Ultra-Low Device Quiescent Current
* Startup Under Load at 0.7V Input Voltage
* Operating Input Voltage Range:0.7 V to 5.5 V
* Pass-Through Function during Shutdown
* Overvoltage Protection
* Overtemperature Protection via Thermal Shutdown Functionality
Data Lebih lanjut, silakan download disini
Harga : Rp 1.399.000,-
Kamis, 18 Agustus 2011
Solusi Energy Harvesting dari Texas Instrument
"Energy Harvesting (EH) also known as Energy scavenging is the use of ambient energy to provide electrical power for small electronic and electrical devices.
An Energy Harvesting System consists of an Energy Harvester Module and a processor/transmitter block. The Energy Harvester module captures milli-watts of energy from light, vibration, thermal or biological sources. A possible source of energy also comes from RF such as emitted from cell phone towers. The power is then conditioned and stored within a battery, an efficient quick charging capacitor or one of the newly developed thin film batteries. The system is then triggered at the required intervals to take a sensor reading, through a low power system. This data is then processed and transmitted to the base station. This kind of EH System eliminates the dependency of the system on battery power and reduces the need to service the system." Texas Instrument
Chip yang telah diproduksi :Low Power RF
| CC1101 | low-cost sub-1 GHz transceiver designed for very low-power wireless applications | |
| CC2500 | Low Cost, Low-Power 2.4 GHz RF Transceiver Designed for Low-Power Wireless Apps in the 2.4 GHz ISM B | |
| CC1110F32 | Sub-1GHz System-on-Chip with MCU and 32kB Flash memory | |
| CC430F6137 | 16-Bit Ultra-Low-Power MCU, 32KB Flash, 4KB RAM, CC1101 Radio, AES-128, 12Bit ADC, USCI, LCD driver | |
| CC110L | Value Line Transceiver | |
| CC1190 | 850 - 950MHz RF Front End | |
| CC430F5137 | 16-Bit Ultra-Low-Power MCU, 32KB Flash, 4KB RAM, CC1101 Radio, AES-128, 12Bit ADC, USCI | |
| CC1020 | Single-Chip FSK/OOK CMOS RF Transceiver for Narrowband Apps in 402-470 and 804-940 MHz Range | |
| CC430F5133 | 16-Bit Ultra-Low-Power MCU, 8KB Flash, 2KB RAM, CC1101 Radio, AES-128, 12Bit ADC, USCI | |
| CC2520 | Second generation 2.4 GHz ZigBee/IEEE 802.15.4 RF transceiver |
| TPS61200 | IC BOOST SYNC ADJ 1.2A |
| TPS62240 | IC BUCK SYNC ADJ 0.3A |
| TPS6122X | IC BOOST SYNC ADJ 50MA 3.3v, 5v , adj |
| TPS780xx | Voltage Regulator 1.22V, 2.3V, 2.7V, 3V and 3.3V |
| TPS62230 | IC BUCK SYNC 2.5V 0.5A |
| TPS781xx | LDO REG 150MA 1.22V , 3.3V |
| TPS6212x | IC BUCK SYNC ADJ 75MA |
| MSP430F249 | MCU 16BIT 60K FLASH |
| MSP430F413 | MCU 16BIT 8K FLASH |
| MSP430F2132 | MCU 16BIT 8K FLASH |
| MSP430F2274 | MCU 16BIT 32K FLASH |
| MSP430F2370 | MCU 16BIT 32K FLASH |
| MSP430F5xx | MCU 16BIT RISC |
| CC430XX | MCU 16B W/RF CORE 8K,16K,32K |
Evalution Board produksi Texas yang berhubungan dengan Energy Harvesting
1. MSP-EXP430FR5739 BOARD EXPERIMENTER FOR MSP430
2. eZ430-RF2500-SEH Solar Energy Harvesting Development Tool
3. CC1101EMK433 - CC1101EMK433 50M8831
4. 2.4 GHz SimpliciTI™ Protocol on Stellaris®
5. CC1190 Evaluation Module Kit
6. CC1020EM Evaluation Module 433 Mhz
7. CC1020EM Evaluation Module 868 Mhz
8. CC1020-CC1070DK 433 MHz Development Kit
9. DK-EM2-2520Z 2.4 GHz ZigBee Wireless Networking on Stellaris®
10. CC2520DK CC2520 Development Kit
11. TPS61200EVM-179 Evaluation Module
12. TPS61220EVM-319 Evaluation Module
13. TPS62230/31/32 6V Input, 2.5V Output, 0.5A Evaluation
14. TPS62122 Evaluation Module
TPS61200EVM-179 Evaluation Module
The TPS61200EVM-179 is an evaluation module for the TPS61200 low input voltage synchronous boost converter. The TPS61200 provides a power supply solution for products powered by either a single-cell, two-cell, or three-cell alkaline, NiCd or NiMH, or one-cell Li-Ion or Li-polymer battery.Features
* Input voltage: 0.3 V to 5.5 V
* Startup into full load at 0.5 V input voltage
* Adjustable output voltage: 1.8 V to 5.5 V
* Switch current limit: 1.5 A (max)
* More than 90% efficiency at:
* 600 mA output current at 3.3 V (VIN ≥ 1.2 V)
* 600 mA output current at 5 V (VIN ≥ 3.3 V)
* Quiescent current: < 55 μA
* Package: 3x3 QFN
Harga : Rp 999.000,-
CC2520DK CC2520 Development Kit
The CC2520 Development Kit includes hardware and software that allows quick testing of the CC2520 RF performance and offers a complete platform for development of advanced prototype RF systems and for evaluation of the CC2520 right out of the box. The kit can be used for range testing using the pre-programmed PER tester running on the MSP430F2618.Use SmartRF® Studio to perform RF measurements. The radio can be easily configured to measure sensitivity, output power and other RF parameters. All I/O from the CC2520 are available on pin connectors on the SmartRF®05EB and on the CCMSP-EM, allowing easy interconnection to other devices or controllers. These connectors are also compatible with logic analyzer probes for easy debugging.
The SmartRF05+CC2520EM can be utilized as a capture device for the SmartRF Packet Sniffer and the Sensor Network Analyzer from Daintree.
Features
The development kit contains the following components:
* 3 x SmartRF®05EB
* 3 x CC2520EM evaluation modules
* 3 x Antennas
* 2 x CCMSP-EM430F2618
* 1 x MSP-FET430UIF debug interface
* 3 x USB cables
* Documents
* TI Packet Sniffer (runs on CC2520EM + SmartRF®05EB)
A free, code size limited edition of IAR Embedded Workbench (IAR Kickstart) is available from the IAR Systems website www.iar.com or from the TI MSP430 homepage www.ti.com/msp430.
Info lebih lanjut, silakan download disini
harga : Rp 13.266.000,-
DK-EM2-2520Z 2.4 GHz ZigBee Wireless Networking on Stellaris®
The Stellaris® 2.4 GHz ZigBee Wireless Networking Kit from Texas Instruments provides a low-power RF network solution for customers' end equipment. The solution combines TI's Z-Stack implementation of the ZigBee and ZigBee Pro protocols with the new Stellaris EM2 expansion board and the Chipcon 2.4 GHz 802.15.4 evaluation module along with the full suite of tools an engineer needs to develop and prototype ZigBee applications with Stellaris. The DK-EM2-2520Z wireless kit works with our most popular Stellaris microcontroller development kit, the DK-LM3S9B96 (sold separately).
ZigBee software is aimed at addressing the market need for a cost-effective, standards-based wireless networking solution that supports low data-rates, low-power consumption, security, and reliability. Such networks typically contain a large number of battery-operated devices networked through an array of routers that report data to a central coordinator. This includes applications in markets such as remote monitoring and control and sensor networking.
The Stellaris® ZigBee solution allows software application developers to become familiar with the operation of the CC2520EMK evaluation module using their Texas Instruments' Stellaris embedded microcontroller platform without having to be concerned about the RF portion of the system. The Stellaris EM2 expansion board facilitates the connection of up to two wireless expansion modules using SPI as the primary interface to the DK-EM2-2520Z module.
Features
The 2.4 GHz ZigBee Wireless Networking Kit has the following features:
* Supports ZigBee (ZigBee 2006 and ZigBee PRO 2007 feature sets)
* Supports both the Home Automation and Smart Energy application profiles
* Secure, self-healing mesh networking capability
* Worldwide market acceptance and interoperability
* Low-cost and low-power
Info lebih lanjut, silakan download disini
Harga : Rp 5.499.000,-
ZigBee software is aimed at addressing the market need for a cost-effective, standards-based wireless networking solution that supports low data-rates, low-power consumption, security, and reliability. Such networks typically contain a large number of battery-operated devices networked through an array of routers that report data to a central coordinator. This includes applications in markets such as remote monitoring and control and sensor networking.
The Stellaris® ZigBee solution allows software application developers to become familiar with the operation of the CC2520EMK evaluation module using their Texas Instruments' Stellaris embedded microcontroller platform without having to be concerned about the RF portion of the system. The Stellaris EM2 expansion board facilitates the connection of up to two wireless expansion modules using SPI as the primary interface to the DK-EM2-2520Z module.
Features
The 2.4 GHz ZigBee Wireless Networking Kit has the following features:
* Supports ZigBee (ZigBee 2006 and ZigBee PRO 2007 feature sets)
* Supports both the Home Automation and Smart Energy application profiles
* Secure, self-healing mesh networking capability
* Worldwide market acceptance and interoperability
* Low-cost and low-power
Info lebih lanjut, silakan download disini
Harga : Rp 5.499.000,-
Selasa, 16 Agustus 2011
CC1020-CC1070DK 433 MHz Development Kit
The CC1020 single chip transceiver and the CC1070 single chip transmitter provide extensive features and great flexibility, which make the chips suitable for a very large number of applications and system requirements. The CC1020 and CC1070 are especially suited for narrowband systems. The CC1020/1070DK development kit is primarily designed to make it easy for designers to evaluate transceiver and transmitter performance and in a minimum of time develop their own applications.The CC1020/1070DK development kit includes two CC1020EB evaluation boards, two CC1020EMX evaluation modules and one CC1070EM evaluation module. The CC1020EMX includes the CC1020 transceiver chip with the external components necessary for operation. The CC1070EM includes the CC1070 transmitter chip with the external components necessary for operation. The evaluation modules are mounted onto the CC1020EB, which is equipped with a voltage regulator and a PC interface circuitry. Using the CC1020EB connected to a PC running the SmartRF® Studio software, various CC1020 and CC1070 system parameters can be changed and tested.
Features
A complete development kit includes:
2 CC1020EB evaluation boards
2 CC1020EMX evaluation modules
1 CC1070EM evaluation module
2 PC parallel port extension cables
6 Adapters
2 Antennas
5 CC1020 samples
5 CC1070 samples
1 CC1020/1070 Quick Start User Manual
Harga : Rp 12.227.000,-
CC1020EM Evaluation Module 868 Mhz
The CC1020 single chip transceiver provides extensive features and great flexibility, which makes the chip suitable for a very large number of applications and system requirements. The CC1020 is especially suited for narrowband systems. The CC1020EMK in combination with a CC1020/1070DK development kit is primarily designed to make it easy for designers to evaluate transceiver performance and in a minimum of time develop their own applications.This evaluation kit includes two CC1020EM 868 MHz modules and antennas. The CC1020EMs are add-on daughter boards that require a CC1020/1070DK development kit for evaluation and development.
Features
A complete Evaluation Kit includes:
2 CC1020 868 MHz evaluation modules which contains:
* CC1020 chip
* Required external components
2 Antennas
Info Lengkap, silakan Download disini
A complete Evaluation Kit includes:
2 CC1020 868 MHz evaluation modules which contains:
* CC1020 chip
* Required external components
2 Antennas
Info Lengkap, silakan Download disini
Harga : Rp 3.036.000,-
CC1020EM Evaluation Module 433 Mhz
The CC1020 single chip transceiver provides extensive features and great flexibility, which makes the chip suitable for a very large number of applications and system requirements. The CC1020 is especially suited for narrowband systems. The CC1020EMK in combination with a CC1020/1070DK development kit is primarily designed to make it easy for designers to evaluate transceiver performance and in a minimum of time develop their own applications.
This evaluation kit includes two CC1020EM 433 MHz modules and antennas. The CC1020EMs are add-on daughter boards that require a CC1020/1070DK development kit for evaluation and development.
Features
A complete Evaluation Kit includes:
2 CC1020 433 MHz evaluation modules which contains:
* CC1020 chip
* Required external components
2 Antennas
Info Lengkap, silakan Download disini
Harga : Rp 3.036.000,-
This evaluation kit includes two CC1020EM 433 MHz modules and antennas. The CC1020EMs are add-on daughter boards that require a CC1020/1070DK development kit for evaluation and development.
Features
A complete Evaluation Kit includes:
2 CC1020 433 MHz evaluation modules which contains:
* CC1020 chip
* Required external components
2 Antennas
Info Lengkap, silakan Download disini
Harga : Rp 3.036.000,-
CC1190 Evaluation Module Kit
The CC1190EMK contains two CC1190 Evaluation Modules (CC1190EM) and antennas. The CC1190 is a cost effective and high performance RF Front End with an embedded PA and LNA. The CC1190EM, when connected with to a sub-1GHz radio (850-950 MHz) with a coax cable, allows you to evaluate the RF front end, extend existing prototypes, and perform RF measurements with better range, sensitivity and output power. This requires that you already have some other complete Sub-1 GHz development kit, like the CC1101DK868-915 or CC1110-CC1111DK.
Features
The kit contains
* 2 x CC1190EM tuned for the 915 MHz frequency band
* 2 x 915 MHz antennas
* Quick Start Guide
Info lebih lanjut, Silakan Download Disini
Harga : Rp 2.022.000,-
Features
The kit contains
* 2 x CC1190EM tuned for the 915 MHz frequency band
* 2 x 915 MHz antennas
* Quick Start Guide
Info lebih lanjut, Silakan Download Disini
Harga : Rp 2.022.000,-
2.4 GHz SimpliciTI™ Protocol on Stellaris®
The Stellaris® 2.4 GHz SimpliciTI™ Wireless Kit (DK-EM2-2500S) from Texas Instruments provides a low-power RF network solution for customers’ end equipment. The solution combines TI’s easy-to-use
SimpliciTI™ protocol with the new Stellaris EM2 expansion board and the Chipcon CC2500EM 2.4GHz evaluation module along with the full suite of tools an engineer needs to develop and prototype 2.4GHz wireless embedded applications with Stellaris. The DK-EM2-2500S wireless kit works with our most popular Stellaris microcontroller development kit, the DK-LM3S9B96
The Stellaris® 2.4 GHz SimpliciTI™ Wireless Kit provides
the tools engineers need to set up and develop wireless
applications right out of the box including:
- 1 DK-LM3S9B96-EM2 Expansion Board
- 1 CC2500EMK 2.4 GHz Evaluation Module
- 1 ez430-RF2500 MSP430 Wireless Development Tool
* MSP430F2274 Low power
* 1 AAA battery pack with expansion board (batteries included)
* 1 MSP430 Development Tool CD-ROM
* 1 eZ430-RF USB debugging interface
* 2 eZ430-RF2500T wireless target boards
CD with tools, documentation, and source code
Data lengkap, Silakan Download Disini
Harga : Rp 3.520.000,-
TEXAS INSTRUMENTS - CC1101EMK433 - CC1101EMK433 50M8831
CC1101 is a low-cost sub-1 GHz transceiver designed for very low-power wireless applications. The circuit is mainly intended for the ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency bands
at 315, 433, 868, and 915 MHz, but can easily be programmed for operation at other frequencies in the 300-348 MHz, 387-464 MHz and 779-928 MHz bands.
The RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data rate up to 600 kbps.
at 315, 433, 868, and 915 MHz, but can easily be programmed for operation at other frequencies in the 300-348 MHz, 387-464 MHz and 779-928 MHz bands.
The RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data rate up to 600 kbps.
Info Lebih Lanjut , silakan Download disini
Harga : Rp 2.568.000,-
eZ430-RF2500-SEH Solar Energy Harvesting Development Tool
The eZ430-RF2500-SEH is a complete Solar Energy Harvesting development kit to help create a
sensor application with no additional batteries. Inputs are also available for external energy harvesters
such as thermal, piezoelectric, or another solar panel.
The system also manages and stores additional energy in a pair of thin-film rechargeable EnerChips
low self discharge, which is vital for a no-power, energy harvesting system.
The eZ430-RF2500 is used to run the energy harvesting application. It is a complete USB-based MSP430
wireless development tool and provides all the hardware and software necessary to use the
MSP430F2274 microcontroller and CC2500 2.4-GHz wireless transceiver. It includes a USB debugging
interface that allows for real-time, in-system debugging and programming for the MSP430, and it is also
the interface to transfer data to a PC from the wireless system.
The integrated temperature and RF signal strength indicators can be used to monitor the environment,
perpetually powered wireless sensor network based on the ultra-low-power MSP430 microcontroller.
The Solar Energy Harvesting module includes a high-efficiency solar (2.25 in x 2.25 in) panel optimized for
operating indoors under low-intensity florescent lights, which provides enough power to run a wirelesssensor application with no additional batteries. Inputs are also available for external energy harvesters
such as thermal, piezoelectric, or another solar panel.
The system also manages and stores additional energy in a pair of thin-film rechargeable EnerChips
which are capable of delivering enough power for 400+ transmissions. The EnerChips act as an energy
buffer that stores the energy while the application is sleeping and has light available to harvest. The
batteries are environmentally friendly and can be recharged thousands of times. They also have a verylow self discharge, which is vital for a no-power, energy harvesting system.
The eZ430-RF2500 is used to run the energy harvesting application. It is a complete USB-based MSP430
wireless development tool and provides all the hardware and software necessary to use the
MSP430F2274 microcontroller and CC2500 2.4-GHz wireless transceiver. It includes a USB debugging
interface that allows for real-time, in-system debugging and programming for the MSP430, and it is also
the interface to transfer data to a PC from the wireless system.
The integrated temperature and RF signal strength indicators can be used to monitor the environment,
and many external sensors can be used to collect additional data.
eZ430-RF2500-SEH
Features
• Efficient solar energy harvesting module for the eZ430-RF2500
• Battery-less operation
• Works in low ambient light
• 400+ transmissions in dark
• Adaptable to any RF network or sensor input
• Inputs available for external harvesters (thermal, piezo, etc.)
• USB debugging and programming interface with an application backchannel to the PC
• 18 available analog and communications input/output pins
• Highly integrated, ultra-low-power MSP430 MCU with 16-MHz performance
• Two green and red LEDs for visual feedback
• Interruptible push button for user feedback
• Efficient solar energy harvesting module for the eZ430-RF2500
• Battery-less operation
• Works in low ambient light
• 400+ transmissions in dark
• Adaptable to any RF network or sensor input
• Inputs available for external harvesters (thermal, piezo, etc.)
• USB debugging and programming interface with an application backchannel to the PC
• 18 available analog and communications input/output pins
• Highly integrated, ultra-low-power MSP430 MCU with 16-MHz performance
• Two green and red LEDs for visual feedback
• Interruptible push button for user feedback
Informasi lengkap, Silakan Download disini
Harga : Rp 3.120.000
Senin, 15 Agustus 2011
MSP-EXP430FR5739 Experimenter Board
The MSP430FR5739 device on the experimenter board can be powered and debugged via the integrated ezFET, or via TI Flash Emulation Tool, like the MSP-FET430UIF.
Features
- Integrated MSP430FR5739 :
- 16KB FRAM / 1KB SRAM
- 16-Bit RISC Architecture up to 8-MHz
- 2x Timer_A Blocks, 3x Timer_B Block
- 1x USCI (UART/SPI/IrDA/I2C ) Blocks, 16Ch 10-Bit ADC12_B, 16Ch Comp_D, 32 I/Os
- 3 axis accelerometer
- NTC Thermister
- 8 Display LED's
- Footprint for additional through-hole LDR sensor
- 2 User input Switches
- Connections
- Connection to MSP-EXP430F5438
- Connection to most Wireless Daughter Cards (CCxxxx RF)
- User Experience
- Preloaded with out-of-box demo code
- 4 Modes to test FRAM features:
- Mode 1 - Max write speed
- Mode 2 - Flash write speed emulation
- Mode 3 - Fast sampling with writes using accelerometer
- Mode 4 - Fast sampling with writes using Thermistor
- Mode 1 & Mode 2 include ULP option to turn off display & optimize for power management
Harga : Rp 596.500
Minggu, 14 Agustus 2011
Solusi Energy Harvesting dari Linear Technology
" Linear Technology Corporation (NASDAQ: LLTC, NASDAQ-100) designs, manufactures and markets a broad line of standard high performance analog integrated circuits. Applications for the company's products include telecommunications, cellular telephones, networking products, notebook and desktop computers, video/multimedia, industrial instrumentation, automotive electronics, factory automation, process control, and military and space systems.
The company was founded in 1981 by Robert H. Swanson, Jr. and Robert C. Dobkin.[1] In August 2010, Forbes called the company "one of the tech industry's most profitable companies" Wikipedia
manufacturer mempunyai solusi energy harvesting yang cukup lengkap yaitu Vibration (Piezo), PhotoVoltaic (Solar) and Thermal (TEC, TEG, Thermopiles, Thermocouples)
Produk yang sudah ada dipasaran diantaranya
Lebih lengkap termasuk harga silakan download disini
Ada beberapa Eval board atau module yang mendukung komponen IC diatas yaitu :
1. DC1568A - BOARD, DEMO, FOR LT3652EDD
2. DC1053A-H - BOARD, DEMO, FOR, LTC3526LBEDC-2
3. DC1227A, BOARD EVALUATION FOR LTC3534
4. DC1584A - BOARD, DEMO, FOR LTC4070EDDB
The company was founded in 1981 by Robert H. Swanson, Jr. and Robert C. Dobkin.[1] In August 2010, Forbes called the company "one of the tech industry's most profitable companies" Wikipedia
manufacturer mempunyai solusi energy harvesting yang cukup lengkap yaitu Vibration (Piezo), PhotoVoltaic (Solar) and Thermal (TEC, TEG, Thermopiles, Thermocouples)
Produk yang sudah ada dipasaran diantaranya
| LT3652 | Solar |
| LT3652HV | Solar |
| LTC3105 | Solar |
| LTC3108 | Thermoelectric |
| LTC3108-1 | Thermoelectric |
| LTC3109 | Thermoelectric |
| LTC3388 | |
| LTC3526L | - |
| LTC3534 | - |
| LTC3535 | - |
| LTC3588-1 | Piezoelectric |
| LTC3588-2 | Piezoelectric |
| LTC4070 | - |
| LTC4071 | - |
Ada beberapa Eval board atau module yang mendukung komponen IC diatas yaitu :
1. DC1568A - BOARD, DEMO, FOR LT3652EDD
2. DC1053A-H - BOARD, DEMO, FOR, LTC3526LBEDC-2
3. DC1227A, BOARD EVALUATION FOR LTC3534
4. DC1584A - BOARD, DEMO, FOR LTC4070EDDB
DC1584A - BOARD, DEMO, FOR LTC4070EDDB
LTC4070EDDB: Simple Low-Iq Battery Charger/Protector With NTC Thermistor Input
Demonstration Circuit DC1584A is a Simple Low-Iq Battery Charger/Protector With NTC Thermistor featuring the LTC4070EDDB
Harga : Rp 1.999.000
Demonstration Circuit DC1584A is a Simple Low-Iq Battery Charger/Protector With NTC Thermistor featuring the LTC4070EDDB
- Description
- BOARD, DEMO, FOR LTC4070EDDB
- Silicon Manufacturer:Linear Technology
- Kit Contents:Board
- SVHC:No SVHC (15-Dec-2010)
- Core Architecture:Power Management - Battery
- Core Sub-Architecture:Battery Charger
- MCU Supported Families:LTC4070
- Type:Battery Charger
Harga : Rp 1.999.000
DC1227A, BOARD EVALUATION FOR LTC3534
Demontration Circuit 1227A is a wide VIN, high efficiency, fixed frequency synchronous Buck-Boost Converter using the LTC3534EDHC. The LTC3534EDHC buck-boost topology operates with input voltages above, below or equal to the output voltage making the product ideal for multi-cell Alkaline/NiMH or single Lithium-Ion/Polymer applications where the output voltage is within the battery voltage range.The LTC3534EDHC operates with a 2.4V to 7V input voltage range and VOUT range from 1.8V to 7V. The demonstration board has been designed to operate with VIN from 3.6V to 6.4V and VOUT is set to 5.0V with an output current up to 500mA.
Referensi lengkap , Silakan Download Disini
Harga : Rp 2.750.000
LINEAR TECHNOLOGY - DC1053A-H - BOARD, DEMO, FOR, LTC3526LBEDC-2
Demonstration circuits1053A-E through 1053AH are high efficiency synchronous boost converters capable of operating with an input voltage range from 0.8V to 5.5V. The 2X2 mm DFN thermally enhanced package with a 1MHz switching frequency (2MHz for -2 versions) and the 550mA internal switches provide a very tiny solution. The LTC3526L family also features output disconnect and the input voltage can be greater or less than the output voltageThis demonstration circuit allows the user to quickly evaluate the LTC3526L performance.
Individual jumpers are provided for selecting several regulated output voltages and a low quiescent current shutdown. Terminals on the board allow easy hookup to an input supply and output load.
Referensi lengkap , Silakan Download Disini
Harga : Rp 2.800.000,-
Sabtu, 13 Agustus 2011
LINEAR TECHNOLOGY - DC1568A - BOARD, DEMO, FOR LT3652EDD
BOARD BATTERY CHARGER SOLAR PWR
Demonstration Circuit 1568A is a 2A Monolithic Multi-Chemistry battery charger for solar power applications featuring the LT3652EDD. The LT3652 is a complete mid-power Li-Ion battery charger that can operate
over a wide input voltage range. The charger employs a 3.3V float voltage feedback reference that allows the battery float voltage to be adjusted up to 14.4V. R10 and R11, in the demonstration circuit, set the float resistor divider. The charger is a CC/CV charger with a
maximum charge current of 2A. A precondition feature trickle charges a low-voltage battery, and bad battery detection provides a signal if the battery doesnt respond to preconditioning.
The LT3652EDD is available in a 12-lead (3mm × 3mm) DFN surface mount package with an exposed pad
maximum charge current of 2A. A precondition feature trickle charges a low-voltage battery, and bad battery detection provides a signal if the battery doesnt respond to preconditioning.
The LT3652EDD is available in a 12-lead (3mm × 3mm) DFN surface mount package with an exposed pad
Referensi silakan Download Disini
Harga Rp 3.100.000
Jumat, 12 Agustus 2011
Energy Harvesting Solution
"Energy harvesting (also known as power harvesting or energy scavenging) is the process by which energy is derived from external sources (e.g., solar power, thermal energy, wind energy, salinity gradients, and kinetic energy), captured, and stored for small, wireless autonomous devices, like those used in wearable electronics and wireless sensor networks.
Energy harvesters provide a very small amount of power for low-energy electronics. While the input fuel to some large-scale generation costs money (oil, coal, etc.), the energy source for energy harvesters is present as ambient background and is free. For example, temperature gradients exist from the operation of a combustion engine and in urban areas, there is a large amount of electromagnetic energy in the environment because of radio and television broadcasting" wikipedia
ada beberapa vendor sudah berpartisipasi dalam pengembangan energy harvesting. Beberapa penelian baru untuk menyempurnakan solusi ini telah banyak dilakukan. Kami berusaha menyediakan tools, komponen dan board simulasi energy harvesting yang berguna untuk penelitian lanjut terutama bagi mahasiswa yang akan mengambil Tugas Akhir.Berikut solusi energy Harvesting dari beberapa vendor terkenal
Langganan:
Postingan (Atom)
