Pyroelectric Infrared PIR Sensor

Infrared Radial Sensor

  * Dual Compensating Elements
 * Excellent Operating Stability
 * Supply Voltage: 3-15V
 * Narrow Sense Window for Directional Sensing
 * Body Dimensions: 9.1mm Dim, 4.5mm High , Pins  - 13.5mm High

Harga :
1pc         = Rp 15.000
2 - 10pcs   = Rp 12.000
11 - 100pcs = Rp 8.000

PIR001 PIR Motion Sensor Detector 

 * infrared sensor with control circuit boards
 * Detector range: 7m
 * Detector angle: 100°
 * Power Voltage: 4.5 -- 20V DC
 * Level Output: 3.3V(2.7V-5V customizable)

Harga :
1pc         = Rp 80.000
2 - 10pcs   = Rp 75.000
11 - 100pcs = Rp 60.000

Simple RFID Reader 10-bit USB port

ZY308 Series RFID reader operation is simple, fast reader. Part of the standard HID devices do not need to install the driver, card number can be read in any edit box (for example: Notepad this, Word and other text editing software), this feature is suitable for extended features in existing software, without having to do the original software any changes;
● communication modes: standard HID communication;
● Interface: full speed USB device interface, compatible with USB V2.0 , universal serial bus interface;
● power supply: USB Universal Serial Bus interface power supply;
● Operating frequency: 125 KHz ;
● maximum sensing distance: 3 to 10 CM ;
Support Card Type: EM series, 4001 series and compatible RF ID card;
● power consumption: less than 0.5 W ;
● Dimensions: 110 × 80 × 30MM
● Operating environment: Temperature 0 - 50 ° C , humidity: 50-95RH , Pressure: 88-106Kpa .
● involving membership management, identification of occasions, example: clubs, campuses, government, enterprises, social security, toll management, Internet cafes and other.

Anda dapat memiliki produk ini dengan harga yang sangat bersahabat

1pc         = Rp 172.000
2 - 10pcs   = Rp 153.000
11 - 100pcs = Rp 133.000

Arduino Sensor Shield V5

Arduino Sensor Shield V5.0 sensor expansion board on the basis of preserving the V4.0 version of the advantages of still only stack design, 

PCB Immersion Gold processing technology, the motherboard will not only Arduino Duemilanove 2009 controller of all digital and analog interfaces to the steering gear line order form extended out ad hoc IIC interface 32 Servo controller interface .

Bluetooth module communication interface, SD card module communication interface, APC220 radio frequency module communication interface, RB URF v1.1 ultrasonic sensor interface, 12864 LCD serial line with parallel interface, independent of the expansion to a more easy-to-use convenience. Arduino beginner, do not have cumbersome complex circuit connection and headache, will simplify the circuit on the true meaning of this sensor expansion board can easily connect the commonly used sensor, a sensor only needs a universal 3P sensor cable (regardless of digital cable and analog cable), complete the circuit connection, write the Arduino program is downloaded to the Arduino Duemilanove controller reads the sensor data, or receive wireless module return data, operation processing, final easily complete your mutual.

Anda dapat membeli shield diatas dengan harga yang sangat murah 

1pcs        = Rp 109.000

2 - 10pcs   = Rp 95.000

11 - 100pcs = Rp 79.000

 

Arduino Proto Shield with Mini Breadboard

Tampak Atas

Tampak Bawah

This expansion board based on the Arduino open source prototyping suitable mix Arduino 328  / UNO / Duemilanove , even in the compatible with Mega1280/2560 interface. Add-On design allows you to arbitrary superposition of the expansion board, more convenient DIY or plug wire cabling the enthusiasts often used way.

Features:
- The leads where power and GND
- Compatible with Arduino NG, Diecimila, Duemilanove, UNO, ADK and any Arduino-clone
- With a restart button
- ICSP interface
- The DIP jack
- Reserved SOIC patch location and USB patch pin position
- Two 3mm LED lights
- Reserve 6mm button a


Shipping list:
- Proto Shiled x 1
- Mini bread board  x 1

Anda bisa mendapapatkan keunggulan shield ini dengan harga yang sangat bersahabat

1pc       = Rp 99.000
2 - 10pcs = Rp 89.000

Arduino Ethernet Shield R3

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the  Ethernet library  to write sketches which connect to the Internet via a Standard  RJ45  Ethernet jack. using the Shield.

The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). You can access the on-board SD card slot using the SD library which is included in the current Arduino build.

The latest revision of the shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up. The reset button on the shield resets both the W5100 and the Arduino board.

Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general i / o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card , but it must be kept as an output or the SPI interface won't work.

Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

Anda dapat memiliki keunggulan Arduino Ethernet Shield Rev3 dengan harga bersahabat

1pc         = Rp 312.000
2 - 10pcs   = Rp 289.000
11 - 100pcs = Rp 259.000

Arduino Pro Mini ATMEGA328P 5V

Arduino pro mini ATMEGA328P 5V/16M improved version of the MCU module

The professional version of the Arduino Mini Pro is a microcontroller board. It has 14 digital input / output pins (of which 6 can be used as PWM outputs), 8 analog inputs, a 16MHz resonator, a reset button, mounting hole pin head.

Technical parameters:

1. 14 Digital input / output ports RX, TX D13, D2 ,
2. or 8 analog input port A0 to A7
3. The TTL level serial transceiver port RX / TX
4. 6 PWM ports, D3, D5 , D6, D9, D10, D11
5. Using Atmel Atmega328P-AU microcontroller
6. supports serial download
7. Support for external 3.3V ~ 12V DC power supply
8. Support 9V battery-powered
9. clock frequency 16MHz
10.Size: 21 * 36 (mm)

Anda dapat mendapatkan keunikan Arduino Pro Mini dengan harga yang sangat bersahabat

1pc         = Rp 119.000
2 - 10pcs   = Rp 99.000
11 - 100pcs = Rp 75.000

Arduino Nano

Tampak Belakang

Tampak Depan

Arduino Nano is a base with ultra-small open source code Simple i / o platform, compared with the prior version of USB Arduino Diecimila account for a significant advantage of the Arduino the Nano in size, that can be used to develop a need to run independently, and has The interactive effects of electronic supplies; developed can be used to connect to a computer with the interactive work done in collaboration with Flash, Processing, Max / Msp, PD, VVVV software.

The Arduino Nano technology parameters:
- The 1.12 digital input / output port D2 to D13,
- Eight analog input ports A0 to A7 3.
- The TTL level serial transceiver port RX / TX 4.6 PWM ports, D3 D5, D6, D9, D10, D11 .
- Using Atmel Atmega328P-AU microcontroller USB download and power supply 7.
- Supports external 5V ~ 12V DC power supply

Temukan keunikan Arduino Nano dengan harga bersahabat 

Harga :
1pcs      = Rp 209.000
2 - 10pcs = Rp 195.000
11 - 100pcs = Rp 169.000

Arduino Leonardo with Header

Tampak Belakang

Tampak Depan

Arduino Leonardo is a the Arduino team recently launched low-cost Arduino controller. It has 20 digital input and output ports, 7 PWM ports and 12 analog input. Compared to other versions of the Arduino using a separate USB-Serial converter chip uses a single-chip solution, the Leonardo innovative. Only with a Atmega32u4 USB communication and control. This innovative design reduces the cost of Leonardo. The original ecological support Atmega32u4 USB characteristics can let the Leonardo modeled as the mouse and keyboard, and greatly improve the applications. Arduino Leonardo need Arduino IDE1.01 version of the new version of the. Arduino Leonardo ordinary Arduino some obvious differences, 

the specific content see the Arduino Leonardo guidance document: http://arduino.cc/en/Guide/ArduinoLeonardo

Specifications

• Controller: ATmega32u4
• goods recorded: 16 MHz
• Operating voltage: 5V
• Input Voltage (recommended) :7-12V
• Digital IO port: 22 (D0-D13, D14-MISO D15-SCK, D16-MOSI D18-23 [A0-A5)
• PWM channel: 7 (D3, D5, D6, D9, D10, D11, D13)
• analog input: 12 (A0-A5, D4-A6, D6-A7, D8-A8 ,-A9 D9, D10-A10, D12-A11)
• 5V digital / analog port maximum permissible current: 40 mA
• 3.3V digital / analog port maximum permissible current: 50 mA
• Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by the bootloader
• SRAM: 2.5 KB (ATmega32u4)
• EEPROM: 1 KB (ATmega32u4

Anda dapat mendapatkan produk Arduino Leonardo dengan harga bersahabat

1pc = Rp 219.000